Skip to main content

ATMEGA-32 Pin-out Diagram

Overview
The Atmel®AVR®ATmega32 is a low-power CMOS 8-bit microcontroller based on the AVR enhanced RISC architecture. By executing powerful instructions in a single clock cycle, the ATmega32 achieves throughputs approaching 1 MIPS per MHz allowing the system designer to optimize power consumption versus processing speed.
AVR spin-out diagrams

Block diagram:-

The Atmel®AVR®AVR core combines a rich instruction set with 32 general purpose working registers. All the 32 registers are directly connected to the Arithmetic Logic Unit (ALU), allowing two independent registers to be accessed in one single instruction executed in one clock cycle. The resulting architecture is more code efficient while achieving throughputs up to ten times faster than conventional CISC microcontrollers. The ATmega32 provides the following features: 32Kbytes of In-System Programmable Flash Program memory with Read-While-Write capabilities, 1024bytes EEPROM, 2Kbyte SRAM, 32 general purpose I/O lines, 32 general purpose working registers, a JTAG interface for Boundary scan, On-chip Debugging support and programming, three flexible Timer/Counters with compare modes, Internal and External Interrupts, a serial programmable USART, a byte orientedTwo-wire Serial Interface, an 8-channel, 10-bit ADC with optional differential input stage with programmable gain (TQFP package only), a programmable Watchdog Timer with Internal Oscillator, an SPI serial port, and six software selectable power saving modes. The Idle mode stops the CPU while allowing the USART, Two-wire interface, A/D Converter, SRAM, Timer/Counters, SPI port, and interrupt system to continue functioning. The Power-down mode saves the register
contents but freezes the Oscillator, disabling all other chip functions until the next External Interrupt or Hardware Reset. In Power-save mode, the Asynchronous Timer continues to run, allowing the user to maintain a timer base while the rest of the device is sleeping. The ADC Noise Reduction mode stops the CPU and all I/O modules except Asynchronous Timer and ADC, to minimize switching noise during ADC conversions. In Standby mode, the crystal/resonator Oscillator is running while the rest of the device is sleeping. This allows very fast start-up combined with low-power consumption. In Extended Standby mode, both the main Oscillator and the Asynchronous Timer continue to run. The device is manufactured using Atmel’s high density nonvolatile memory technology. The On-chip ISP Flash allows the program memory to be reprogrammed in-system through an SPI serial interface, by a conventional nonvolatile memory programmer, or by an On-chip Boot program running on the AVR core. The boot program can use any interface to download the application program in the Application Flash memory. Software in the Boot Flash section will continue to run while the Application Flash section is updated, providing true Read-While-Write operation. By combining an 8-bit RISC CPU with In-System Self-Programmable Flash on a monolithic chip, the Atmel ATmega32 is a powerful microcontroller that provides a highly-flexible and cost-effective solution to many embedded control applications.
The Atmel AVR ATmega32 is supported with a full suite of program and system developmenttools including: C compilers, macro assemblers, program debugger/simulators, in-circuit emulators, and evaluation kits.
AVR Block diagram

Pin Description:-

VCC: Digital supply voltage.
GND: Ground.
Port A (PA7-PA0): Port A serves as the analog inputs to the A/D Converter. Port A also serves as an 8-bit bi-directional I/O port, if the A/D Converter is not used. Port pins can provide internal pull-up resistors (selected for each bit). The Port A output buffers have symmetrical drive characteristics with both high sink and source capability. When pins PA0 to PA7 are used as inputs and are externally pulled low, they will source current if the internal pull-up resistors are activated. The Port A pins are tristated when a reset condition becomes active,even if the clock is not running.
Port B (PB7-PB0): Port B is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port B output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port B pins that are externally pulled low will source current if the pull-up resistors are activated. The Port B pins are tri-stated when a reset condition becomes active, even if the clock is not running.
Port C (PC7-PC0): Port C is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port C output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port C pins that are externally pulled low will source current if the pull-up resistors are activated. The Port C pins are tri-stated when a reset condition becomes active, even if the clock is not running. If the JTAG interface is enabled, the pull-up resistors on pins PC5(TDI), PC3(TMS) and PC2(TCK) will be activated even if a reset occurs. The TD0 pin is tri-stated unless TAP states that shift out data are entered. Port C also serves the functions of the JTAG interface and other special features of the ATmega32.
Port D (PD7-PD0): Port D is an 8-bit bi-directional I/O port with internal pull-up resistors (selected for each bit). The Port D output buffers have symmetrical drive characteristics with both high sink and source capability. As inputs, Port D pins that are externally pulled low will source current if the pull-up resistors are activated. The Port D pins are tri-stated when a reset condition becomes active, even if the clock is not running. Port D also serves the functions of various special features of the ATmega32.
RESET: Reset Input. A low level on this pin for longer than the minimum pulse length will generate a reset, even if the clock is not running. Shorter pulses are not guaranteed to generate a reset.
XTAL1: Input to the inverting Oscillator amplifier and input to the internal clock operating circuit. XTAL2: Output from the inverting Oscillator amplifier.
AVCC: AVCC is the supply voltage pin for Port A and the A/D Converter. It should be externally connected to VCC, even if the ADC is not used. If the ADC is used, it should be connected to VCC through a low-pass filter.
AREF: AREF is the analog reference pin for the A/D Converter.

Comments

Popular posts from this blog

8051 Simple Programs

Sum of 8-bit Numbers Stored in Memory Here  we will discuss about 8051 programs but we can't discuss about all of the 8051 instructions. For programming 8051 we should know about assembler directives as well as instruction set. Click  here to download Atmel c51 user guide that will discuss about 8051(c51 family microcontroller) instruction set, assembler directives, c51 cross assembler from Atmel.  Program ORG 00H MOV R0,#50H   ; get memory location in memory pointer R0 MOV R1,#51H   ; get memory location on memory pointer register R1 MOV A,@R0       ; get content of memory location 50H to accumulator ADD A,@R1        ; add content of A with content of memory location 51H and store result in A MOV R0,#52H    ; get 52H to memory pointer R0 MOV@R0,A         ; copy content of A to memory location 52H END Add 16-bit Numbers Program ORG 00H MOV DPTR,#2040H   ; get 2040H into DPTR MOV A,#2BH              ; get lower byte of second 16-bit number on accumulator MO

Introduction to 8051 embedded C

For 8051 we need to include the file reg51.h. This file contains the all the definitions of 8051 registers. With this information C compiler produces hex file that can be downloaded into the ROM of the microcontroller. It is important to note that the size of the hex file produced by the assembly language is much larger than the hex file produced by C compiler. Apart from this fact, there is many reasons for writing programs in C instead of assembly: ●It is much easier and less time consuming to write programs in C assembly. ●C is more flexible; it is easier to modify and update. ●Programming in C allows to use code available in function libraries. ●Program written inC for one microcontroller is portable to other microcontrollers with little or no modifications. Data Types in 8051 Embedded C The table shown below lists the data types that are available in typical C51 compiler. The gives information about the size of the data variable and it's value range. Data type

8051 Keyboard Interfacing

Keyboards are organized in a matrix of rows and columns. The CPU accesses both rows and columns through ports. Therefore, with two 8-bit ports, an 8 x 8 matrix of keys can be connected to a microprocessor. When a key is pressed, a row and a column make a contact. Otherwise, there is no connection between rows and columns. In IBM PC keyboards, a single microcontroller takes care of hardware and software interfacing. A 4x4 matrix connected to two ports. The rows are connected to an output port and the columns are connected to an input port. Grounding Rows and reading Columns:- 8051 keyboard interfacing It is the function of the microcontroller to scan the keyboard continuously to detect and identify the key pressed. To detect a pressed key, the microcontroller grounds all rows by providing 0 to the output latch, then it reads the columns. If the data read from columns is D3 – D0 =1111, no key has been pressed and the process continues till key press is detected. If one of t